angle joint的例句大全

The structural type of T-joint and angle joint in construction steel structure were expounded, the test characteristics of these structural type were explored, and the key point of control and test method for detecting flaw by supersonic was proposed in this paper.

本文论述建筑钢结构T型接头及角接接头的结构型式，探讨了这种结构型式的检测特点，提出了用超声波探伤的检测方法及控制要点。

Based on this, the paper selects typical welding joint in the shipbuilding process, mainly including the butt welding of web plate, the butt welding of panel, the butt welding of plate, the angle joint of plate and web plate.

基于此本文选取船体建造过程中典型的焊接对接接头，该焊接接头主要由平板的对接、腹板的对接、面板的对接以及腹板和平板的角接组成。

Quality control and test of T-joint and angle welded joint in construction steel structure

建筑钢结构T型及角接焊接接头的质量控制与检测

Winston knelt down and examined the angle-joint of the pipe.

温斯顿跪下来,查看水管的接头.

The muscular function change in the lower extremity according to the angle of joint was assessed.

评定下肢肌肉功能随关节角度变化而发生的变化；

Ultrasonic Flaw Location of Angle Welded Joint with Inserted Take Over

插入式接管角接接头超声波探伤缺陷定位

A Study of Relation Between Fractal Dimension and Frictional Angle of Joint Profile

岩体节理形貌的分形维数与摩擦角的关系研究

The profile butt-welding is the most typical welding structure of ship welding, it includes the butt welding of outer plate, the butt welding of panel, the butt welding of web plate, the angle joint of outer plate and web plate.

型材对接焊是船舶焊接中最典型的焊接结构，包含了外板的对接焊缝、面板的对接焊缝、腹板的对接焊缝和腹板与外板的角接缝四条焊缝。

The machine is mainly used for extrusion and connection of 45 ° seam casement window with angle joint structure.

门窗单头组角机主要用于角码结构的平开门窗45°接缝的挤压联结。

It is presented that the differential pressure orifice flowmeter and the angle joint differential pressure measuring structure used in the test are the applied technologies of H2O2/ kerosene engine test.

提出了压差式孔板流量测量和角接式取压结构在过氧化氢/煤油发动机试验中的应用技术。

Design of the Injection Mould for Right Angle Water Supply Pipe Joint with Plastic Lining Internal Thread

内螺纹衬塑直角管接头注射模设计

By the knee joint angle curve got from 3-D Gain Analyzer, we approach the knee joint angle curve to achieve the most approximation between prosthesis and body.

针对Zebris三维步态分析仪采集到的膝关节角度曲线，对膝关节角度进行逼近，以实现假肢对健肢的最大程度地逼近。

A novel blind joint angle and delay estimation method based on trilinear model is presented. Oversampled signal of array antennas is processed by fast Fourier transform, and results show that the Fourier transformed signal has trilinear model characteristics.

提出一种新的盲联合角度-时延的估计方法，对阵列天线输出的过采样样本的Fourier变换后信号进行分析，结果表明，此信号具有三线性模型特征。

A novel blind joint angle and delay estimation method in uniform circular array based on trilinear model was presented.

提出了均匀圆阵中一种盲联合角度和时延的估计方法（BJADE）。

Blind joint angle and delay estimation method in uniform circular array

均匀圆阵中盲联合角度和时延估计方法

The joint shapes suited for CO_2 welding are designed Under which weld quality is still assured but the groove angle and size of fillet weld are reduced. By ways of these the productivity is increased and cost decreased.

提出了适合于CO2焊特点的接头形式，该接头形式在保证焊接质量前提下，减小了对接焊的坡口角度及角焊缝的焊脚尺寸，可以提高焊接生产率，降低成本。

A Joint Correlation Approach based on the Angle and Energy Trace Information of Targets

一种利用目标方位和能量信息的联合关联方法

A Novel Approach for Joint Angle and Delay Estimation in DS-CDMA Systems

一种新的DS-CDMA系统多径角度时延联合估计方法

Study showed that angle deformation of T joint is changed along the welded seam length.

研究表明,T形接头的角变形沿焊缝长度方向是变化的.

It is assumed that the robotic manipulator has only joint angle position measurements.

假定机器人只有联合角位置测量.